square with 4leads type led lamps doc. no : qw0905-LUY9653H-30B rev. : b date : 22 - may. - 2006 LUY9653H-30B data sheet ligitek electronics co.,ltd. property of ligitek only pb lead-free parts
note : 1.all dimension are in millimeter tolerance is 0.25mm unless otherwise noted. 2.specifications are subject to change without notice. directivity radiation part no. LUY9653H-30B package dimensions page 1/5 ligitek electronics co.,ltd. property of ligitek only 0.5 4.4 0.5 3.5 0.5 2.5 0.5 0.4 5.08 0.3 1.55 5.08 3.0 r0.7 7.62 0.5 7.62 0.5 1.9 c1.25 cathode anode 30 60 75%100% 25%50% -30 0 25% 75%50% 100% -60 0
note : 1.the forward voltage data did not including 0.1v testing tolerance. 2. the luminous intensity data did not including 15% testing tolerance. emitted typical electrical & optical characteristics (ta=25 ) LUY9653H-30B part no yellow algainp/gap material forward voltage @20ma(v) luminous intensity @20ma(mcd) dominant wave length dnm spectral halfwidth nm 20 590 water clear lens color 1300 900 1.72.6 max. min.min. typ. viewing angle 2 1/2 (deg) 65 ligitek electronics co.,ltd. property of ligitek only electrostatic discharge( * ) operating temperature storage temperature power dissipation reverse current @5v peak forward current duty 1/10@10khz forward current 2000 esd t opr tstg -40 ~ +85 -40 ~ +100 ir pd i fp i f 10 130 100 70 absolute maximum ratings at ta=25 parameter symbol uy(h) ratings v a mw ma ma page 2/5 unit static electricity or power surge will damage the led. use of a conductive wrist band or anti-electrosatic glove is recommended when handing these led. all devices, equipment and machinery must be properly grounded. * part no. LUY9653H-30B
fig.3 forward voltage vs. temperature fig.5 relative intensity vs. wavelength ambient temperature( ) r e l a t i v e i n t e n s i t y @ 2 0 m a wavelength (nm) f o r w a r d v o l t a g e @ 2 0 m a n o r m a l i z e @ 2 5 fig.4 relative intensity vs. temperature ambient temperature( ) r e l a t i v e i n t e n s i t y @ 2 0 m a n o r m a l i z e @ 2 5 forward voltage(v) fig.1 forward current vs. forward voltage f o r w a r d c u r r e n t ( m a ) forward current(ma) fig.2 relative intensity vs. forward current r e l a t i v e i n t e n s i t y n o r m a l i z e @ 2 0 m a ligitek electronics co.,ltd. property of ligitek only 1.0 0.1 1.0 10 100 1000 1.0101001000 0.0 0.5 1.0 1.5 2.0 2.5 3.0 -40-200204060 1.0 1.1 1.2 500 550600 0.0 0.5 1.0 2.03.04.05.0 80100 0.8 0.9 -20 -40 40 20 080100 60 2.0 0.0 0.5 1.0 1.5 2.5 3.0 650 typical electro-optical characteristics curve uy(h) chip 3/5 page part no. LUY9653H-30B
60 seconds max 260 c3sec max 5 /sec max 260 120 temp( c) time(sec) 150 50 100 2 /sec max 25 0 preheat 0 page 4/5 ligitek electronics co.,ltd. property of ligitek only soldering condition(pb-free) 1.iron: soldering iron:30w max temperature 350 c max soldering time:3 seconds max(one time) distance:2mm min(from solder joint to body) 2.wave soldering profile dip soldering preheat: 120 c max preheat time: 60seconds max ramp-up 2 c/sec(max) ramp-down:-5 c/sec(max) solder bath:260 c max dipping time:3 seconds max distance:2mm min(from solder joint to body) part no. LUY9653H-30B
mil-std-202: 210a mil-std-750: 2031 jis c 7021: a-1 1.t.sol=260 5 2.dwell time= 10 1sec. this test intended to determine the thermal characteristic resistance of the device to sudden exposures at extreme changes in temperature when soldering the lead wire. solder resistance test this test intended to see soldering well performed or not. solderability test 1.t.sol=230 5 2.dwell time=5 1sec mil-std-202: 208d mil-std-750: 2026 mil-std-883: 2003 jis c 7021: a-2 ligitek electronics co.,ltd. property of ligitek only this test is conducted for the purpose of detemining the resistance of a part in electrical and themal stressed. the purpose of this test is the resistance of the device under tropical for hours. the purpose of this is the resistance of the device which is laid under condition of low temperature for hours. the purpose of this is the resistance of the device which is laid under condition of high temperature for hours. the purpose of this is the resistance of the device to sudden extreme changes in high and low temperature. 1.under room temperature 2.if=20ma 3.t=1000 hrs (-24hrs, +72hrs) thermal shock test high temperature high humidity test 1.ta=105 5 &-40 5 (10min) (10min) 2.total 10 cycles 1.ta=65 5 2.rh=90%~95% 3.t=240hrs 2hrs high temperature storage test low temperature storage test operating life test 1.ta=105 5 2.t=1000 hrs (-24hrs, +72hrs) 1.ta=-40 5 2.t=1000 hrs (-24hrs, +72hrs) reliability test: test itemtest condition mil-std-202: 107d mil-std-750: 1051 mil-std-883: 1011 mil-std-202:103b jis c 7021: b-11 mil-std-883:1008 jis c 7021: b-10 jis c 7021: b-12 mil-std-750: 1026 mil-std-883: 1005 jis c 7021: b-1 page 5/5 description reference standard part no. LUY9653H-30B
|
